7.SUPPLY CIRCUITGroundConductorOutlet Box GreenGroundLeadGround toDownrodBLACKWHITEWHITEBLACKBLUEGREENWHITEBLUEBLACKWHITEFigure 14Diagram indicates op
8.RubberwasherBladearmFigure 15BladeScrewsAttaching the Fan BladesStep 1 Attach the blades to the blade arms using three screws and rubber
Installing the Mounting PlateStep 1. Remove 1 of the 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove)Step 2.
Operating Your Fan 10. TouchingceilingFigure 19WARNINGTO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDERSWHILE INSTALLING, BALANCING
Here are some suggestions to help you maintain your fan1.Because of the fan's natural movement, some connections may become loose.
ProblemFan will not start.Fan sounds noisy.Solution1.Check circuit fuses or breakers.2. Check line wire connections to the fan and switch wire connect
These are approximate measures. They do not include Amps and Wattage used by the light kit.RPMCFMN.W. G.W.C.F.52"1202.37'11.64kgs13.2kgs0.2
Fecha de compra Lugar de compraN de modelo.N de serieNumero de vendedorUPC11221785247139217Garantía Limitada de 15 AñosLOS VENTILADORES PROGRESS LI
Tabla de ContenidoNormas de seguridad ...
Date Purchased Store PurchasedModel No.Serial No. Vendor No.UPC11221785247139217PROGRESS LIGHTING 15-Year Limited WarrantyPROGRESS LIGHTING FAN MOTO
1. Normas de seguridadNOTA!LEER Y GUARDAR TODAS LAS INSTRUCCIONES!1. Para reducir el riesgo de eléctrocución, asegurarse de que la eléctricidad se ha
Desembalar el ventilador y revisar el contenido. Debe tener los siguientes elementos:Cómo desembalar el ventilador 2.6. Conjunto de motor del venti
Herramienta necesariasDestornillador Phillips, destornillador normal, llave de tuercas ajustable, escalera de tijera, y cortadoras de alambr
4.6. Alinee los agujeros de la parte inferior del tubo con los agujeros del aro en la parte superior de la cubierta del motor (Figura 7). Introduzca c
5.Tornillos yarandela deseguridadCollarinEmpacadurade gomaInstalacion próxima al techo1. Retire el anillo de la marquesina girándolo hacia la derecha
6. Instalacion del Ventilador a la Caja ElectricaLa caja de distribucion y el soporte de la estructura debe estar seguramente montado y ser c
7.CIRCUITO DE A LIMENTACIÓNConductora tierraCaja de distribuciónHilo de tierraverdeConexión atierra para la barra descendenteNEGROBLANCOBLANCONEGROAZU
8.15Juntar Las Palas del VentiladorPaso 1: Se pegan las palas a los soportes usando los tornillos y las arandelas de goma provistos como indi
Figura 17Figura 189.InstalacióN del Cubierta de InterruptoresNOTA: Antes de comenzar la instalación, desconecte la alimentación apagando el i
ADVERTENCIAPARA REDUIR RIESGO DE LESIONES PERSONALES. NO DOBLAR LOS SUJET ADORES DE ASPAS MIENTRAS SE REALIZA LA INSTALACIÓN. EL BALANCEO DE LAS ASPAS
Safety Rules...Unpac
11. Cómo cuidar del ventiladorHe aqui algunas sugerencias para ayudarle el mantenimiento del ventilodor. 1. Debido al movimiento natural de
Resolución de problemas 12.ProblemaEl ventilador noarranca.El ventilador hace mucho ruido.Solución1. Revisar los fusibles o interruptores de circuitos
13. Especificaciones 11,64 kgs 133,2 kgs 2,37'Tamaño delVentiladorVelocidad Voltios AmperiosVatiosRPMCFMN.W. G.W.52"(132 cm)BajaMedianaAlta1
1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning.2. All wiri
Unpack your fan and check the contents. You should have the following items:1. 2. Mounting plate (located inside canopy)3. Canopy assembly4. Ball/dow
3. Installing Your Fan Tools RequiredPhillips screw driver, straight slot screw driver, adjustable wrench, step ladder, and wire cutters.Mo
Hanging the FanREMEMBER to turn off the power.Follow the steps below to hang your fan properly.NOTE: This ceiling fan is supplied with two typ
5. Figure 9Figure 10Motor collarClose-to-Ceiling Mounting1. Remove the canopy ring from the canopy. (Figure 5)2. Remove the mounting plate
6.Figure 12Figure 13 Figure 13-1Close- to-Ceiling MountingStandard MountingInstalling Fan to the Electrical BoxThe outlet box and support structu
Comments to this Manuals